Publication UMA-EN-P – November Table of Contents . User Manual UM to assign an IP address to the MicroLogix. controller. Publication INC-EN-P – October Important . Manual UM .. publication UM, for more information on surge suppression. rm_-en-p – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Document Number IN UM

Author: Tojasar Tojataur
Country: Ghana
Language: English (Spanish)
Genre: Love
Published (Last): 23 February 2013
Pages: 108
PDF File Size: 9.44 Mb
ePub File Size: 15.74 Mb
ISBN: 772-9-13730-169-8
Downloads: 97137
Price: Free* [*Free Regsitration Required]
Uploader: Kazrabar

IN – Rockwell Automation

WARNING Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. Use AWG 14 wire. Remove the mounting template.

The Belden cable has two signal wires black and clearone drain wire, and a foil shield. MicroLogix Instruction Set Reference Manual RM A reference manual that contains data and function files, instruction set, and troubleshooting information for MicroLogix It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts.

You can also contact a special Customer Support number for initial help in getting your product up and running. If you would like a manual, you can: Make sure that the placement of the controller on the DIN rail meets the recommended spacing requirements see Controller Spacing on page 12 for more information. Soal meeting 9th Part of speech: Holding the controller, pry downward on the latch until the latch locks in the open position. Failure to remove strip before operating can cause overheating.

  DIE BIBLIOTHEK VON BABEL BORGES PDF

Leave the protective debris strip attached until you are finished wiring the controller and any other devices. The analog output can support a voltage function as shown in the following illustration. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc.

Wiring category 1 2 – on signal ports 2 – on power ports 3 – on communications ports Terminal screw torque 0. Linea centrale della guida DIN. Finger-safe cover TIP If you wire the terminal block with the finger-safe cover removed, you may not be able to put it back on the terminal block if the wires are in the way. The terminals will accept a 6. The Battery Low indicator on the LCD display of the controller shows the status of the replaceable battery.

1766-IN001 – Rockwell Automation

However, because of the variety of applications and environments where analog controllers are installed and operated, it is impossible to ensure that all environmental noise will be removed by the input filters.

Power supply inrush current V AC: The enclosure must have suitable flame-retardant properties 166 prevent or minimize the spread of flame, complying with a flame spread rating of 5VA, V2, V1, V0 or u001 if non-metallic. In no event will Rockwell Automation, Inc.

Installation Assistance If you experience a problem within the first 24 hours of installation, please review the information that’s contained in this manual. Do not touch the connector pins or other sensitive areas.

Scripting must be enabled to use this site.

Once wiring is complete, remove protective debris strip. Follow these steps uj001 install your controller on the DIN rail.

  CORROSION FILIFORME PDF

Wiring Your Analog Channels Analog input circuits can monitor voltage signals and convert them to serial digital data as shown in the following illustration. Store the equipment in appropriate static-safe packaging when not in use. Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this product.

Industrial Automation Wiring and Grounding Guidelines Debris strip ATTENTION Do not remove the protective debris strip until after the controller and uj001 other equipment in the panel near the controller are mounted and wiring is complete.

Remove the mounting template from inside the back cover of this document. Power Loss in Transmission Lines. For AC-powered controllers, this connection must be made um01 safety purposes. Locate your controller as far as possible from power 11766, load lines, and other sources of electrical noise such as hard-contact switches, relays, and ac motor drives.

Refer to the mounting template inside the back cover of this document. Output 2, 3 and 4 may be used like the other FET transistor outputs, but in addition, within a limited current range, they may be operated at a higher speed. However, if your product is not functioning and needs to be returned, follow these procedures.

The interior of the enclosure must be accessible only by the use ym001 a tool. All cables connected to the product must remain in the enclosure or be protected by conduit or other means.