The autofrettage process is widely used in various industries for increasing operating pressures for advanced industrial, automotive, aerospace and defense . The detailed numerical comparison between the two different autofrettage processes points to the fact that the swage autofrettage process is. The swage or mechanical autofrettage process is routinely used in many industries including nuclear industry, where enhanced strength-to-weight ratio is .
|Published (Last):||10 April 2015|
|PDF File Size:||4.16 Mb|
|ePub File Size:||14.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
The effect is that the inner layers of the metal are put under compression by the outer layers in much the same way as though an outer layer of metal had been shrunk on as with a built-up gun.
Please help xutofrettage this article by adding citations to reliable sources. Autofrettage is a metal fabrication technique in which a pressure vessel is subjected to enormous pressure autovrettage, causing internal portions of the part to yield plastically, resulting in internal compressive residual stresses once the pressure is released.
The amount of initial underbore and oversize of the die are calculated to strain the material around the bore past its elastic limit into plastic deformation. This page was last edited on 29 Octoberat Views Read Edit View history. The goal of autofrettage is to increase the durability of the final product.
Retrieved from ” https: In early practice of autofrettage of a gun barrel, the barrel was pressurized hydraulically. The tube is subjected to internal pressure of sufficient magnitude to enlarge the bore and in the process the inner layers of the metal are stretched in tension beyond their elastic limit.
Autofrettage – Wikipedia
The end result is an inner surface of the gun barrel with a residual compressive stress able to counterbalance the tensile stress that would be induced auhofrettage the gun is discharged. The next step is to subject the compressively strained inner layers to a low-temperature heat treatment which results in the elastic limit being raised to at least proceas autofrettage pressure employed in the first stage of the process. The method has been patented by the Norwegian oil service company, Meta, which uses it to connect concentric tubular components with sealing and strength properties outlined above.
In modern practice, a slightly oversized die is pushed slowly through the barrel by a hydraulically driven ram.
Inducing residual compressive stresses into materials can also increase their resistance to stress corrosion cracking ; that is, non-mechanically-assisted cracking that occurs when a material is placed in a corrosive environment in the presence of tensile stress.
The term autofrettage is also used to describe a step in manufacturing of composite overwrapped pressure vessel COPV where the liner is expanded by plastic deformationinside the composite overwrap. Unsourced material may be challenged and removed. Autorrettage the autofretatge layers of the tube are also stretched, the degree of internal pressure applied during the process is such that they are not stretched beyond their elastic limit.
Because the outer layers remain elastic they attempt to return to their original shape; however, they are prevented from doing so completely by the new permanently stretched inner layers. From Wikipedia, the free encyclopedia.
This article needs additional citations for verification. This means that the inner layers have been stretched to a point where the steel is no longer able to return to its original shape once the internal pressure has been removed. While autofrettage will induce some work hardeningthat is not the primary mechanism of strengthening. Finally, the elasticity of the barrel can autoftettage tested autofrettge applying internal pressure once more, but this time care is taken to ensure autofreytage the inner layers are not stretched beyond their new elastic limit.
In addition the material has a higher tensile stress as a result of the heat treatment process.
The strain is proportional to the stress applied within the elastic limit; therefore the expansion at the outer layers is less than at the bore. Articles needing additional references from June All articles needing additional references.
Archived from the original PDF on The reason why this is possible is that the stress distribution through the walls of the tube is non-uniform. June Learn how and when to remove this template message.
The technique has been applied to the expansion of tubular components down hole in oil and gas wells. A residual compressive stress remains on the barrel’s inner surface, even after final honing and rifling.