compensated versions of the popular CA series. Gate protected P-Channel MOSFET (PMOS) transistors are used in the input circuit to. CA Printer Friendly Version. 15MHz, BiMOS Operational Amplifier with MOSFET Input/CMOS Output. Datasheet &. Related Docs. Description. Key. CA 15MHz, Bimos Operational Amplifier With MOSFET Input/cmos Output. 15MHz, BiMOS Details, datasheet, quote on part number: CA

Author: Faelrajas Negor
Country: Puerto Rico
Language: English (Spanish)
Genre: Literature
Published (Last): 24 October 2008
Pages: 230
PDF File Size: 8.56 Mb
ePub File Size: 17.77 Mb
ISBN: 290-1-21694-822-8
Downloads: 80633
Price: Free* [*Free Regsitration Required]
Uploader: Shakar

Operation at 5V is not recommended for temperatures below 25oC. Jan 9, 8. The power supply already has decoupling caps on its output and I cant see any noise at all on the power rails. I also noticed that noise on pin8 begins at the same time as the output goes awry.

IC CA DATASHEET EPUB

A sample circuit is shown below The special ability of this op-amp is to work with high frequencies ; it has a CMRR of 80dB and the rise time is as low as 0. In this comparator mode, the output of IC1 goes high when its pin 3 gets fa higher voltage datasheey pin 2. Skip to main content.

These are high gain op-amp; ic ca datasheet voltage on the inverting input can be datqsheet almost equal to Vin. Do you have decoupling capacitors at the power supply pins? This pin is connected to ca130 ground of the system Negative voltage can also be used.

CA MOSFET Op-Amp Pin Diagram, Specifications, Equivalent & Datasheet

The presence of PMOS transistors at the inputs results in common mode input voltage datasbeet down to 0. Let it be assumed again Q8 6 that the input-terminal bias Terminals 2 and 3 is such that Q12 RL the output terminal No. A biasing circuit provides two potentials for function as a differential-to-single-ended converter to provide common use in the first and second stages.

  ENDOPROTEZA STAWU KOLANOWEGO REHABILITACJA PDF

Pin1 forms the emitter of output transistor.

(PDF) CA3130 Datasheet download

In this single-and dual-supply service. Jun 6, 3, 5, In typical linear applications where the Input-Current Variation with Temperature differential voltage is small and symmetrical, these The input current of the CA Series circuits is typically incremental changes are of about the same magnitude as 5pA at 25oC.

Its output will be in the zero state in the off mode. Is there a better opamp to use instead of the ?. It should be noted, with CMOS input logic, e. It is important to read and understand the specs of any part before you try to use it. Thank you for your request. Information furnished by Intersil is believed to be accurate and reliable. Q1, Q2, and Q5 in IC2 are configured as a and R2 are used to bias the CA to the mid-point of the low impedance, temperature-compensated source of supply-voltage and R3 is the feedback resistor.

Jan 9, 6. Remember that the operational dwtasheet is a high gain, differential voltage amplifier.

Accordingly, the cx3130 is cautioned to verify that data sheets are current before placing orders. As such I am powering it with a single sided 5V supply and want the input and output to datasheft from 0 to 5V at least close to this. All Intersil semiconductor products are manufactured, assembled and tested under ISO quality systems certification.

A CMOS transistor-pair, capable ic ca datasheet swinging the output voltage to within 10mV of either supply-voltage terminal at very high values of load impedanceis employed as the output circuit.

CA3130 Datasheet

You May Also Like: Jan 9, 9. I tried the ohm resistor and.

  LORD TEDRIC SPACE PIRATES PDF

Anatomy of a Viral Kickstarter: In such cases, heat- PA CA 6 sinking can also very markedly reduce and stabilize input 3 current variations. The CA can work in a Single supply voltage or in a dual supply mode. When the inverting input is more than the non-inverting then logic low 0 will be the output. The described later, illustrates the practical use of the CA in datasheeet stage of the CA limits the bandwidth in this a single-supply voltage-follower application.

Typical op amp loads are readily driven by the output stage. I tried a cap across the input power pins just in case, but it made no difference. Intersil semiconductor products are sold by description only. For information regarding Intersil Corporation and its products, see web site http: How Does a Fuse Work?

One voltage is called the reference voltage and the other is called the input voltage. Note the input common mode range. It exhibits very fast response and high speed of performance.

The biasing circuit for the constant-current of essentially zero current drain in the output stage under the source is subsequently described. The source of bias potentials This makes it ideal for voltage followers and other switching related applications.

When an op amp is connected with negative feedback voltage follower is one examplethe two inputs will be at the same voltage.

The resistor ladder is an 0. Thanks everyone for the help, I learnt a few things about opamps along the way though. Here the pin3 is inverting input and pin2 Non inverting input. This sinks current and the load turns on.